SERVICE BULLETIN NEW MAINTENANCE SCHEDULE, CHECKLIST AND ENGINE PRESERVATION FOR ROTAX® ENGINE TYPE 275, 501, 505, 535 SB-505-010 SB-535-009 MANDATORY Repeating symbols: Please, pay attention to the following symbols throughout the Service Bulletin emphasizing particular information. ▲ WARNING: Identifies an instruction, which if not followed, may cause serious injury or even death. ■ CAUTION: Denotes an instruction which if not followed, may severely damage the engine or could lead to suspension of warranty. ◆ NOTE: Information useful for better handling. 1) Planning information 1.1) Engines affected all certified 2-stroke aircraft engines from start of serial production: 275 501 505 (Series) 535 (Series) 1.2) Concurrent ASB/SB/SI und SL In addition to this Service Bulletin the following additional Service Bulletin/Service Instruction must be observed and complied with: - Service Bulletin-SB-505-005, title “Piston pin bearing, conversion to reinforced design” current issue. - Service Instruction-SI-11-1996, title “Engine preservation for 2-stroker UL-engines” current issue. 1.3) Reason Based on long testing experience of these certified ROTAX® 2-stroke engines the maintenance schedule became updated. 1.4) Subject New maintenance schedule, checklist and engine preservation for ROTAX® engines type 275, 501, 505, 535. 1.5) Compliance Incorporation into the respective documentation of the aircraft manufacturer, at the latest December 31, 2006. 1.6) Approval The technical content is approved under the authority of DOA Nr. EASA.21J.048. 2) Material Information none d03857 SEPTEMBER 5, 2006 Initial issue Copyright - ROTAX® Current valid documentation see: www.rotax-aircraft-engines.com SB-505-010, SB-535-009 page 1 of 6 3) Accomplishment / Instructions Accomplishment All the measures must be taken and confirmed by the following persons or facilities: - ROTAX® -Airworthiness representative - ROTAX -Distributors or their Service Centers ® - Persons approved by the respective Aviation Authority - Persons with type-specific training ▲ WARNING: Proceed with this work only in a non-smoking area and not close to sparks or open flames. Switch off ignition and secure engine against unintentional operation. Secure aircraft against unauthorized operation. Disconnect negative terminal of aircraft battery. ▲ WARNING: Carry out work on a cold engine only. ▲ WARNING: Should removal of a locking device (e.g. lock tabs, self-locking fasteners, etc.) be required when undergoing disassembly/assembly, always replace with a new one. ▲ WARNING: Following instructions require the replacement of the piston pin bearing from the old version with cage to the cageless version. This procedure is absolutely mandatory to guarantee a safe operation and to get a correct reading when carrying out the conrod bearing clearance tester (see section 3.3.2). 3.1) Pre-flight checks ▲WARNING: Repair as necessary all discrepancies and shortcoming before flight. - Verify ignition "OFF" - Check fuel content. - Inspect for coolant leaks. - Verify spark plug connectors for security. - Inspect engine for oil leaks. - Inspect engine for loose or missing nuts, bolts and screws. - Inspect propeller for splits and chips. If any damage, consult propeller manufacturer for a repair scheme. - Verify security of propeller mounting. - Check throttle and choke actuation for free and full movement. - Inspect exhaust for cracks, security of mounting, springs and hooks for breakage and wear. - Start engine after assuring that area is clear of bystanders. - Single ignition engines check operation of ignition switch (flick ignition off and on again at idle). - Dual ignition engines check operation of both ignition circuits (according OM). - Cheek operation of all engine instruments during warm up. - If possible, visually check engine and exhaust for excessive vibration and unusual noise during warm up. - Verify that engine reaches full power rpm during take off roll. 3.2) Daily checks ▲WARNING: Repair as necessary all discrepancies and shortcomings before flight. - Verify ignition "OFF" - Drain water from fuel tank sump and/or water trap (if fitted). - Inspect carburetor rubber socket or flange for cracks and verify secure attachment. - Verify security and condition of intake silencer and air filter. - Verify security of radiator mounting. Inspect radiators for damage and leaks. - Verify coolant level in overflow bottle and security of cap. - Verify coolant hoses for security, inspect for leaks and chafing. - Inspect engine for coolant leaks (cylinder head, cylinder base and water pump). - Verify oil content for rotary valve gear lubrication and security of oil cap. - Verify oil hoses for security, inspect for leaks and chafing (rotary valve gear lubrication system) - Verify ignition coils/electronic boxes for secure mounting. Check ignition leads and all electrical wiring for secure connections and chafing. - Verify electric starter for secure mounting. - Verify engine to airframe mounting for security and inspect for cracks. d03857 SEPTEMBER 5, 2006 Initial issue Copyright - ROTAX® SB-505-010, SB-535-009 page 2 of 6 - Verify fuel pump mounting for security. Inspect all fuel hose connections, filters, primer bulbs and taps for security, leakage, chafing and kinks. - Verify fuel pump impulse hose for secure connections, inspect for chafing and kinks. - Rotate engine by hand and listen for unusual noises (first double verify that ignition is OFF). - Check propeller shaft bearing for clearance by rocking propeller. - Inspect throttle and choke cables for damage (end fittings, outer casing and kinks and free movement). - Inspect reduction drive for condition and belt tension. d03857 SEPTEMBER 5, 2006 Initial issue Copyright - ROTAX® SB-505-010, SB-535-009 page 3 of 6 3.3) maintenance schedule 3.3.1) Checks & work/ schedule Checks & work 1) 1 Ground run 2 Re-torque cylinder head nuts 2) 3 Carry out CCBCT check on cold engine and record readings in log book. Check to see history of readings and ensure they are within limits and there has not been any sudden increase 4 Re-torque exhaust manifold screws 2) 5 visual check of engine condition 3) 6 Check rewind starter rope 7 Check electric starter gear 8 Inspect spark plugs (according OM) 9 Replace spark plugs (according MM) 10 Check ignition system 11 Check & clean inside spark plug caps+ fixation 12 Lubricate ball joints of exhaust 13 Replace exhaust muffler springs 11) 14 Lubricate contol cables 5) 15 Check propeller balance and tracking 4,5) 16 Inspect propeller mounting bolts 5) 17 Clean and oil air filter 18 Check fuel filter 19 Replace fuel filter 20 Check carburettor(s) and re-adjust (idle speed, cable tension, throttle valve position,….) 21 Clean carburettor(s) and check for wear 22 Check fuel pump (measure fuel pressure) 23 replace fuel pump 24 Check gearbox oil level 8) 25 Replace gearbox oil 8) 26 Check and adjust gearbox, preload of springs (type B gearbox) 8) 27 Replace coolant 28 Replace coolant hoses 29 Check points & condensors 30 check the resistance of the charging coil and replace if neccesary (280- 330 Ohm) 31 Check ignition timing (points versions) 32 Replace points and condensors 33 Replace rotary valve lubrication oil 7) 34 Inspect cylinder head and piston crown 35 Inspect piston rings for free movement 36 Check piston diameter 6) 37 Piston ring: check gap 6) 38 Piston ring: check axial clearance (rectang-ring) 39 Check cylinder diameter 6) 40 Cylinder: check for roundness 6) 41 Replace cylinder head, cylinder base and exhaust gaskets 42 Check decompressor 12) 43 Compression check 44 Inspect piston pin and bearing 45 Replace piston pin and small end bearing 9) 46 Replace outer seals and main bearings if necessary First 2 hr 10 hr XX X 5 hr or 1 yr 12.5 hr or 1 yr X 25 hr or 1 yr Every 50 hr or 2 yr X 100 hr or 3 yr 150 hr or 5 yr 300hr or 6 yr X XX X XX XX X X X X X X X X X X X X XX X X X X X X X X XX X XX X X X X X X X X X X X X X X X 47 Replace fuel hose 48 Replace carb membrane 49 Check compliance with service bulletins 50 check pistons & piston rings 10) 51 inspect crankshaft runout (PTO& MAG) X X X X X 1) at every scheduled maintenance a pre-flight and daily inspection should be carried out 2) and after every replacement of gasket(s) 3) check of rust on outside surface, visual check of cylinder, cylinder head fins and piston condition by removing the exhaust manifold 4) also after any damage 5) according to instructions of manufacturer 6) wear limit see Repair Manual 7) use only oil with good inhibiting properties 8) engine type 275 only 9) if needle cage is installed 10) and use oversize pistons if necessary 11) and whenever necessary 12) only on engines equiped with decompressor SEPTEMBER 5, 2006 Initial issue SB-505-010, SB-535-009 page 4 of 6 d03857 Copyright - ROTAX® 3.3.2) Conrod Bearing Clearance Tester (see Fig. 1) The conrod bearing clearance tester (CBCT) is designed for use on all Rotax 2-stroke engines. The bearing clearance tester is intended to check big end and small end bearing clearances without disassembly of the engine.The conrod bearing clearance tester consists of a dial gauge, plug adaptor with dial gauge fixing screw and pipe connector, dial gauge extension, suction hose and vacuum pump (syringe). The tester can also be used as an indicator for checking ignition timing on all Rotax 2-stroke engines. The maximum reading of the dial gauge must not exceed 0,07mm (0,002756 in.). ◆ NOTE: The measurement is only significant with cageless piston pin bearing. 3.4) Engine preservation If the engine is not going to be used for an extended period of time, certain measures must be taken to protect engine against heat, direct sun light, dampness, corrosion and formation of residues. In particular the water bonded by the alcohol in the fuel causes increased corrosion problems at engine stops or storage. Especially affected are essential engine components such as crankshaft bearings and conrod bearings as well as crank pins and piston pins. For further instructions refer to SI-11-1996. 3.4.1) After each flight Activate choke for a moment before stopping engine 3.4.2) If Engine is Likely to be Stored for more than 8 weeks (or 4 weeks on seaside conditions) - Proceed with preservation prior to engine stop and on the engine at operating temperature - let the engine run at increased idle speed - remove air filters and inject approx. 6 cm³ of preservation oil or equivalent oil into the air intake of each carburetor stop engine - remove spark plugs and inject approx. 20 cm³ preservation oil into each cylinder and slowly turn crankshaft 2 to 3 turns by hand to lubricate top end parts. Refit spark plugs. - drain gasoline from carbs, fuel tank, fuel lines and pump. - drain coolant on liquid cooled engines, to prevent any damage by freezing ▲ WARNING: Generally comply with standard rules for handling of chemicals. Dispose of chemicals as per local enviromental regulations. - Lubricate all carburetor linkages. - Close all openings of the engine like exhaust end pipe, venting tube and air intake to prevent entry of dirt and humidity. - spray all external steel parts with engine oil. - ensure the engine is turned at least one turn of the propeller at least once in every 8 weeks (or 4 weeks on seaside conditions). 3.4.3) If Engine has been Stored for more than 1 year - Carry out complete strip and inspection Approval of translation to best knowledge and judgment - in any case the original text in German language and the metric units (SI-system) are authoritative. d03857 SEPTEMBER 5, 2006 Initial issue Copyright - ROTAX® SB-505-010, SB-535-009 page 5 of 6 4) Appendix The following drawings should convey additional information: 5 6 4 1 3 2 8 7 9 10 11 1 dial gauge 2 plug adapter 3 fixing screw 4 dial gauge extention 5 suction hose 6 syringe 7 piston pin 8 small end bearing 9 conrod 10 big end bearing 11 crank pin fig. 1 07627 d03857 ◆ NOTE: The illustrations in this document show the typical construction. They may not represent full detail or the exact shape of the parts which have the same or similar function. Exploded views are no technical drawings and are for reference only. For specific detail, refer to the current documents of the respective engine type. SEPTEMBER 5, 2006 Initial issue Copyright - ROTAX® SB-505-010, SB-535-009 page 6 of 6